The 6.7L Power Stroke Turbo Diesel badge on the fender of a white heavy-duty pickup, the Ford engine the S&S DCR conversion kit fits

Floorjack Auto Repair · Off I-17 near Happy Valley Rd

CP4 conversion in Phoenix with the S&S DCR kit

The S&S DCR conversion kit for the Ford 6.7 Power Stroke, installed in our own bays. It carries a CARB order, and the emissions equipment stays on the truck.

5 from 92 Google reviews

ASE Certified, GM-certified, UTI-trained Serving Phoenix since 2021

CP4 conversion in Phoenix at Floorjack Auto Repair means taking the Bosch CP4 high-pressure fuel pump off a diesel and fitting a different pump in its place. On the Ford 6.7 Power Stroke, that is the S&S DCR conversion kit, installed in our own bays on the I-17 frontage at Happy Valley Road. Javen Coughlin calls with the price before anything comes off the truck.

CP4 to DCR conversion on the 6.7 Power Stroke

The DCR is a replacement for the Bosch CP4.2 on the Ford 6.7 Power Stroke. DCR stands for Diesel Common Rail, the name of Stanadyne’s pump family. S&S Diesel Motorsport built the Ford version with PurePower Technologies, Stanadyne’s aftermarket division, and S&S’s DCR page says it needs no calibration changes and has not been tested on any other platform.

S&S’s own pages list the 6.7 Power Stroke DCR conversion for model years ending anywhere from 2024 to 2026, but the CARB order stops earlier. Executive Order D-756-7 covers 2011 to 2023, and S&S’s install sheet limits the kit to those years. We fit the DCR on 2024 and newer Super Duty trucks too, so call us with the year before you order anything.

What the DCR conversion kit includes

The S&S DCR kit holds the pump, two new high-pressure lines to the rails, a new low-pressure supply and return line assembly, an adapter plate, a support bracket and the hardware, according to S&S’s installation sheet. The injectors and rails are not part of the kit. The sheet lays the job out in this order:

  • Clean the engine bay with compressed air or low-pressure water before anything comes off.
  • Remove the intake manifolds, cooling fan, fan hub and vacuum pump to reach the CP4.
  • Pull the CP4 and inspect the drive gear, which gets reused.
  • Mount the DCR on its adapter plate and time it to the engine with the cam gear mark and the roll pin on the pump shaft.
  • Fit the new lines and new engine and chassis fuel filters, which S&S recommends, plus a new vacuum pump gasket on 2011 to 2016 trucks.
  • Prime the system with five 30-second ignition cycles, start the truck and check every fitting for leaks.

S&S recommends new fuel filters on every install. On a truck with no fuel problem, we change them when they are due or when you ask.

The rest of our diesel work is on our diesel repair across the Valley page.

The S&S DCR kit holds CARB Executive Order D-756-7, issued in May 2024, and it leaves the truck’s emissions equipment where it is. The order exempts the kit from California Vehicle Code Section 27156 for 2011 to 2023 Ford 6.7 turbocharged diesels. It describes a pump driven by the crankshaft like stock, with fuel pressure still set by the stock regulator and no change to any other engine component or to the calibration.

The DPF, EGR and DEF system stay on the truck, so this is an emissions-intact conversion, not a delete.

The order is California’s exemption, and it says it gives no opinion on warranty or on compliance with other state, federal or local law. Arizona’s statute, A.R.S. 49-541, defines tampering as removing, defeating or altering an emissions control device installed when the vehicle was made. Every conversion kit we install carries a CARB order, and the DCR we install is the S&S kit that carries this one.

DCR conversion cost

As of November 2026, S&S lists the DCR pump kit at $2,400 with a two-year, unlimited-mile warranty. That is the part before labor, and the job takes the intake, fan and vacuum pump off the engine, so labor is a real line on the quote.

At our shop, a DCR swap on a truck whose CP4 has not failed runs roughly $4,000 to $5,000. With the appointment booked and the deposit paid, the truck is usually done in one day.

CP4 conversion in Phoenix is priced after we look at the truck and before anything comes apart, and the price does not move after that. American First Finance splits a bill like this into payments through our financing page and does not require perfect credit.

CP4 to CP3 conversion for the LML Duramax and the 2019 to 2020 Ram

There is no DCR for these trucks. S&S’s CP4 conversion kit for the LML Duramax and for the 2019 and 2020 Ram 6.7 Cummins swaps the CP4.2 for Bosch’s older CP3, under two more CARB orders.

TruckReplacement pumpCARB orderYears in the order
Ford 6.7 Power StrokeS&S DCRD-756-72011 to 2023
Chevrolet and GMC 2500 and 3500, 6.6 Duramax LMLBosch CP3D-756-42011 to 2016
Ram 2500 and 3500, 6.7 CumminsBosch CP3D-756-52019 to 2020

Duramax owners can read about the LML generation on our Duramax repair in Phoenix page. Ram owners should check recall 21V-880 first, because dealers replace the 2019 and 2020 pump free. We install the S&S CP3 kit on both trucks.

OEM parts around the pump

The DCR pump is not an OEM part. It is S&S and PurePower’s aftermarket pump, made to replace the Bosch CP4, and the new lines in the kit are S&S’s too.

Most of what surrounds the pump is the truck’s factory hardware. On a conversion the injectors, rails and rail-to-rail line stay on the truck, and the drive gear, mounting nuts and fuel pressure sensors go back on. Where a job needs parts beyond the kit, such as the vacuum pump gasket and the fuel filters, OEM parts are our default, and we install aftermarket on request with both prices shown.

CP4 conversion in Phoenix before a failure, and after one

A CP4 pump conversion before a failure is the job above: the pump, the lines and the filters, with the injectors and rails left alone. After a failure it is bigger. S&S says the rest of the fuel system has to be cleaned or replaced before a DCR goes on, because debris left behind can damage the new pump. That bigger job is the reason an owner would convert early.

A 2020 Ford F-350 came to us on a tow truck with a split CP4 and metal through the fuel system. It got a contamination kit with OEM injectors and fuel rails, plus a DCR pump, and the whole job is on our CP4 failure repair in Phoenix page, along with the recalls that make a dealer repair free.

Find the shop

Bring your diesel in from across the Valley

We are at 21242 N. Black Canyon Hwy, Suite D, Phoenix, AZ 85027, on the I-17 frontage at Happy Valley Road. Owners come to us for CP4 conversion in Phoenix up I-17 from the city and across the Loop 101 from Glendale, Peoria and Scottsdale. Deer Valley owners are close by.

Floorjack Auto Repair
21242 N. Black Canyon Hwy, Suite D
Phoenix, AZ 85027

Get Directions

Common questions

Answers before you bring it in

We don’t keep the phone around for fun. Call us; we’re glad to help.

Call Us
Will a DCR conversion void my Ford warranty?

Not by itself. Under the federal Magnuson-Moss Warranty Act, Ford can deny a claim only if it shows the outside work caused the failure, and the CARB order says it gives no opinion on warranty. If your truck is still under Ford's warranty and the CP4 fails, ask the dealer first. Our Ford repair in Phoenix page covers when the dealer is the better route.

Can I convert a truck whose CP4 has not failed?

Yes. Most run roughly $4,000 to $5,000 and take one day once the appointment is booked and the deposit is paid. CP4 conversion in Phoenix on a healthy truck goes the same way, and we look at the old filter and housing when the CP4 comes off. A clean filter means the injectors and rails stay. Metal means they go too, and the job becomes a failure repair with a price you approve first.

Is there a DCR for my Duramax or Ram?

No. S&S makes the DCR for the Ford 6.7 only. CP4 conversion in Phoenix on the LML Duramax and the 2019 and 2020 Ram means a CP3 kit under CARB orders D-756-4 and D-756-5, and the table above has the years.

Will the DCR change how my truck runs?

It should not. The CARB order says fuel pressure stays with the stock regulator and the engine calibration does not change, and S&S says the pump adds no power on its own. The pump is timed to the engine at install.

Where are you, and can I leave the truck after hours?

21242 N. Black Canyon Hwy, Suite D, Phoenix, AZ 85027, off I-17 at Happy Valley Road. We are open Monday to Friday, 8 to 5, and closed weekends. A conversion is a booked job, so call (623) 363-5990 or book online, and if you can only come after we close, text first and use the after-hours drop-off.

Schedule Service

Book Your Service Today

Tell us what the vehicle's doing and we'll get it on the schedule. You hear the price before any work starts. No surprises on the invoice.