Floorjack Auto Repair is on the I-17 frontage road at Happy Valley Road. Owner Javen Coughlin is ASE Certified, GM-certified and UTI-trained, and he worked at GM and Buick dealerships before he opened the shop in 2021. Transmission diagnosis, removal and installation happen in our bays. We don’t rebuild transmissions in the shop. When one is worth rebuilding, it goes to a transmission builder in Phoenix. When a replacement unit costs less, we install that instead. GM, Ford and Ram run deepest here, and every make is welcome.
What Phoenix heat does to a transmission
Heat wears out an automatic transmission, and the fluid takes it first. Transmission fluid cools the unit, lubricates it and carries the pressure that applies the clutches inside. The hotter it runs, the sooner it breaks down, and broken-down fluid lets those clutches slip, which makes more heat.
Phoenix driving stacks up the conditions that raise fluid temperature. Summer afternoons often pass 110 degrees. A commute ends in stop-and-go traffic on surface streets after the off-ramp. Trucks tow campers and trailers, and the drive north on I-17 toward Flagstaff is a long climb with that load behind them. Many owner’s manuals list towing, heavy stop-and-go driving and high outside temperatures as severe service, and severe service shortens the fluid interval.
So a transmission that shifted fine in March can start slipping in July.
Slipping doesn’t always mean a new transmission
“My transmission is slipping. Does that mean a new transmission?” Not always. Several of the things that cause slipping sit outside the transmission’s internal parts, and they get ruled out before a rebuild comes up.
What drivers notice: the engine revs up but the car doesn’t speed up to match, a long pause before it goes into drive or reverse, hard or late shifts, a shudder at steady speed that feels like rumble strips, a whine or a clunk, a burnt smell, red fluid under the car, or a check engine light. Some transmissions protect themselves by holding one gear, which drivers call limp mode.
What can be behind it:
- Low or worn-out fluid. Low fluid on its own can cause slipping and late engagement, and burnt or dark fluid points to heat damage. Many newer transmissions have no dipstick, so the level is checked at a check plug, at the temperature the manufacturer specifies.
- A fault the computer has stored. The transmission computer (or the engine computer, on some vehicles) stores fault codes. A scan tool also shows live data such as fluid temperature and whether the transmission is in the gear the computer asked for.
- The engine, not the transmission. A misfire under load can feel like a transmission shudder from the driver’s seat.
- Electrical parts. Shift solenoids, speed sensors, wiring and connectors can all cause slipping or harsh shifts. Some of them can be replaced without pulling the transmission.
- Wear inside the case. Worn clutches, bands or a failing torque converter. This is the one that means the transmission comes out, and it’s when rebuild or replace comes up.
Codes get read the same way as for a check engine light: the code is where testing starts, not the answer.
Transmission work we do
Diagnosis
Done in the shop, before any price for a rebuild or a replacement is quoted. You find out what failed before you’re asked to pay to fix it.
Removal and installation
When a transmission has to come out, we pull it in our bays. When the rebuilt or replacement unit is ready, we install it here too. That part of the job stays with the shop that diagnosed it.
Rebuilds
A transmission worth rebuilding goes to a transmission builder in Phoenix. We remove it, the builder rebuilds it, and we install it.
Replacement units
When a replacement unit costs less than a rebuild, we install that instead. A replacement unit can be remanufactured or used.
Clutches, transfer cases and differentials
Clutch jobs on manual transmissions are done here, and so is work on transfer cases and differentials. On a four-wheel-drive truck, a whine that changes with speed, or a bind or clunk when you shift into four-wheel drive, can come from a differential or the transfer case instead of the transmission.
Transmission work is part of our engine diagnostics and repair service.
Rebuild or replace: cost decides
A rebuild means the transmission is taken apart, the worn and failed parts are replaced, and it’s put back together. A replacement unit is a different transmission installed in place of yours. Either way the transmission comes out of the vehicle, so the labor to remove it and put one back in is part of both prices.
What changes is the cost of the unit. That depends on what failed inside, how much damage it did on the way, and what a replacement for your vehicle costs. We compare the two and go with whichever costs you less. You hear that price, and which way we’re going, before any work starts.
Diagnosed first, priced before any work starts
A transmission price without a diagnosis is a guess, and on a transmission a wrong guess costs a lot. We find the problem, give you the price, and wait for your answer. Nothing goes on the invoice that you didn’t approve. If the number lands at a bad time, financing through American First Finance splits it into payments.
Before you book
Tell us the year, make and model, what the transmission is doing, and when it happens: cold, hot, after the freeway, or only in one gear. Mention any lights on the dash. We’ll get it on the schedule and call you with what we find.
Related pages
- Check engine light in Phoenix: how we read a code and test what it points at before anything gets replaced
- GM repair in Phoenix: Silverado, Sierra, Tahoe and the rest of the GM line, from an owner who worked in GM dealerships
- Duramax repair in Phoenix: the Allison behind the 6.6L and the rest of the diesel side
- Auto repair in North Phoenix: everything else the shop does for the north side of the city